How to Set Up Conductive Gel and Mask Bundles at Home
By 7E Wellness | Published: 2026-10-13
Category: How-to Guides
A step-by-step home setup for conductive gel and microcurrent masks, including lead wire splitter routing, eye and lip mask placement, and gel application checkpoints.
Quick answer
Start with clean, dry skin, apply a thin layer of conductive gel to the eye and lip areas, then attach the adhesive conductive masks and connect the lead wire splitter to your microcurrent device. Run one short, low-intensity session, keeping the gel layer intact and the mask edges sealed. The Conductive Mask Bundle with Lead Wire Splitter is the simplest way to treat eye and lip zones at the same time.
Prep the skin and device before any mask touches your face
Wash and fully dry your face, then wipe the eye and lip areas with a mild toner to remove any oil or makeup residue. Oils block current and weaken the treatment, so this step is not optional. Set your microcurrent device to its lowest intensity and confirm the lead wires are not tangled. If you are using the Conductive Mask Bundle with Lead Wire Splitter, keep the splitter close to the device so the two mask leads have equal slack.
Apply conductive gel only where the mask will sit
Squeeze a pea-sized amount of 4oz ReStore Anti-aging Conductive Gel onto your fingertip and spread a thin, even film over the brow, under-eye, and lip border areas. A thin film is enough; a thick blob can make the adhesive mask slide. If you are using a reusable eye mask, the gel also helps the conductivity bar stay in contact. Wait ten seconds for the gel to settle before placing the mask.
Place the masks and route the lead wire splitter
Peel the adhesive eye mask from its backing and press it gently around the brow and under-eye area, smoothing from the inner corner outward. Do the same with the lip mask, centering it over the lip line. If you are using the bundle, plug both mask leads into the lead wire splitter, then connect the splitter to your device. Keep the wires draped over your ears or away from your face so they do not pull the masks loose during the session.
Run the session and watch for gel dry-down
Turn the device on and slowly raise the intensity until you feel a light tingling, not a sting. Run the session for the time recommended by your device manual, usually under ten minutes for a targeted eye and lip treatment. If the tingling fades or turns sharp, stop and check the gel layer. Dry gel is the most common reason a mask feels uneven or stops conducting, so keep the ReStore gel nearby for a small touch-up.
Remove, clean, and store reusable masks correctly
Turn the device off before removing the masks. Peel each mask slowly from the outer edge, then wipe your skin with a damp cloth to remove leftover gel. Reusable eye masks last about 10-12 treatments or until the conductivity bar no longer stays solid, so check that bar before your next session. Store the masks flat on their backing in a cool, dry place; folding them can crease the conductive layer.
Your at-home setup steps
- Cleanse and dry the treatment zones: Wash your face and pat the eye and lip areas completely dry. Oils and moisture residue can make the mask slide or block current. Checkpoint: skin should feel matte, not tacky, before you apply gel.
- Apply a thin layer of ReStore conductive gel: Use a pea-sized amount and spread it evenly over the brow, under-eye, and lip border. Do not over-apply; a thick layer prevents the adhesive mask from gripping. Mistake to avoid: skipping gel on the lip area because you assume the mask covers it. The mask localizes current, but the gel is what conducts it.
- Attach the eye and lip masks: Peel each mask from its backing and press it gently into place, smoothing from the center outward. For the bundle, connect both mask leads to the lead wire splitter before turning on the device. Checkpoint: mask edges should sit flat with no lifted corners.
- Connect the lead wire splitter and start low: Plug the splitter into your device, drape the wires away from your face, and begin at the lowest intensity. Raise slowly until you feel a light tingle. Mistake to avoid: starting at a medium or high setting. You can always increase, but you cannot undo an uncomfortable first jolt.
- Run one short session and monitor the gel: Treat for the time recommended in your device manual, usually under ten minutes for eye and lip. If the sensation becomes sharp or uneven, stop and reapply a small amount of gel. Checkpoint: the session should feel steady and mild, never hot or stinging.
- Remove, clean, and store the masks: Turn the device off, peel masks slowly from the outer edge, and wipe away leftover gel. Store reusable masks flat on their backing and check the conductivity bar before each use. Next step: replace reusable eye masks once the conductivity bar no longer stays solid, typically after 10-12 treatments.
Products that support this setup
- Conductive Mask Bundle Eye Mask Lip Mask with Lead Wire Splitters: The 7E MyoLift Conductive Mask Bundle includes eye and lip adhesive masks plus a lead wire splitter, allowing a targeted eye and lip microcurrent treatment at the same time. You can treat both zones in one session instead of swapping masks, which saves setup time and keeps the gel layer consistent.
- Eye Masks for Microcurrent Therapy Wholesale: The Eye Masks for Microcurrent Therapy are reusable for 10-12 treatments or until the conductivity bar no longer stays solid. Plan your replacement cycle around that bar condition, not a calendar date, so conductivity stays reliable.
- 4oz ReStore Anti-aging Conductive Gel with Bio-Active Complex: The 4oz ReStore Anti-aging Conductive Gel hydrates skin during treatment and includes anti-aging ingredients. A thin layer keeps current flowing and adds a skin-care step, so you do not need a separate serum before the mask.
